One of my most visited sites is Green Wedding Shoes where I find the most amazing things. Recently I found this post and instantly my creative head started to buzz. I am going to make these but mount them on styrofoam with a line and a weight attached so that I can position them in a swimming pool for a touch of evening ambiance. They would also look amazing hung upside down over a table....... endless possibilities. Going to try them out and will share my flowers with you soon.
Materials:
• Several sheets of poster board (it takes at least two full sheets of poster board per flower)
• Large Plastic Solo Cups (1 per flower)
• Bath poof
• Hot glue gun and extra sticks
• Spray Paint
• Clear Plastic Wrap
• Thin wall electrical conduit, ½” x 10’. Home Depot SKU# 203106
• Halex ½” set screw connectors, Home Depot SKU# 839663
• Raco 3 ½” round cover, Home Depot Internet SKU# 202058390
• Wood Block or bucket filled with sand to help the flower stand up
• Fabric to pool at the base of your stems
Preparing the bath poof:
So we tried to use a whole poof…but it was just too much, so we cut it in half. There is a small rope that goes around the middle of the bath poof. Cut the poof in half leaving one side tied up by the rope. Keep a firm grasp on the rest of the poof. Add a generous amount of glue to the newly cut edge, then cover with a scrap of poster. Re-glue any places that are not secured. Do the same to the other half. Now you can make two flowers. Yay!
• Several sheets of poster board (it takes at least two full sheets of poster board per flower)
• Large Plastic Solo Cups (1 per flower)
• Bath poof
• Hot glue gun and extra sticks
• Spray Paint
• Clear Plastic Wrap
• Thin wall electrical conduit, ½” x 10’. Home Depot SKU# 203106
• Halex ½” set screw connectors, Home Depot SKU# 839663
• Raco 3 ½” round cover, Home Depot Internet SKU# 202058390
• Wood Block or bucket filled with sand to help the flower stand up
• Fabric to pool at the base of your stems
Preparing the bath poof:
So we tried to use a whole poof…but it was just too much, so we cut it in half. There is a small rope that goes around the middle of the bath poof. Cut the poof in half leaving one side tied up by the rope. Keep a firm grasp on the rest of the poof. Add a generous amount of glue to the newly cut edge, then cover with a scrap of poster. Re-glue any places that are not secured. Do the same to the other half. Now you can make two flowers. Yay!
MAKING THE FLOWER
Step one:
Lay the poster board glossy side down. (If the poster does not have a glossy side, it’s just fine.) Rip the poster towards yourself length-wise. Start by ripping pieces that are the entire length of the poster. I’m not going to lie, it takes a little practice to get a good technique.
After you get 5-7 very long petals between 2-4 inches wide, move on to tearing the smaller pieces. It’s good for the petals to curl, because they will begin to flatten out over time and you don’t want a droopy flower….or maybe you do!
Tip: Separate the petals based on size. You need several of each size, but more ofthe medium and small.
Step one:
Lay the poster board glossy side down. (If the poster does not have a glossy side, it’s just fine.) Rip the poster towards yourself length-wise. Start by ripping pieces that are the entire length of the poster. I’m not going to lie, it takes a little practice to get a good technique.
After you get 5-7 very long petals between 2-4 inches wide, move on to tearing the smaller pieces. It’s good for the petals to curl, because they will begin to flatten out over time and you don’t want a droopy flower….or maybe you do!
Tip: Separate the petals based on size. You need several of each size, but more ofthe medium and small.
Step Two:
Cut your cup in half. Then cut 1 inch tabs all the way around it. This will be your base. Hot glue your biggest petals to the OUTSIDE of the cut tabs. The weight of the petals should open the cup into a semi-flat shape.
Cut your cup in half. Then cut 1 inch tabs all the way around it. This will be your base. Hot glue your biggest petals to the OUTSIDE of the cut tabs. The weight of the petals should open the cup into a semi-flat shape.
Step Three:
Continue adding petals to the INSIDE of the cup moving from largest to smallest. Be sure to fill in areas that look empty. Stop before you get to the smallest petals.
Continue adding petals to the INSIDE of the cup moving from largest to smallest. Be sure to fill in areas that look empty. Stop before you get to the smallest petals.
Step Four:
Glue your bath poof to the center. Once the bath poof is glued, add the smaller petals so that they curve up around it.
Glue your bath poof to the center. Once the bath poof is glued, add the smaller petals so that they curve up around it.
Step Five:
Once you are satisfied with the fullness of the flower, lightly dust the center with spray paint.
Tip:Guard the outer petals with newspaper or extra poster so they don’t get sprayed.
Once you are satisfied with the fullness of the flower, lightly dust the center with spray paint.
Tip:Guard the outer petals with newspaper or extra poster so they don’t get sprayed.
Preparing the stem:
I’m going to be honest, my dad did this part – and there is no exact technique. Some have asked if PVC pipe would work. We tried it, but it was too flimsy. Instead, we used thin wall electrical conduit from the electrical department at Home Depot. You also need a screw connector and a round metal outlet cover. If you are confused, print out the picture, take it to the home improvement store and they should know exactly what you need.
Bending the conduit (stem). THIS is the difficult part: Hold the pipe up at an angle, one end resting on the ground. Slightly bend by stepping on the lowest section, move your foot up 8-10” and repeat until you have the curve you want. Be careful and don’t try to bend the conduit all at once, making numerous smaller bends works best. Once the conduit is curved, attach the Halex screw connector onto the flower end of the conduit, knock the center plug out of the Raco round cover plate and secure it to the screw connector (very easy, just sounds confusing).
I’m going to be honest, my dad did this part – and there is no exact technique. Some have asked if PVC pipe would work. We tried it, but it was too flimsy. Instead, we used thin wall electrical conduit from the electrical department at Home Depot. You also need a screw connector and a round metal outlet cover. If you are confused, print out the picture, take it to the home improvement store and they should know exactly what you need.
Bending the conduit (stem). THIS is the difficult part: Hold the pipe up at an angle, one end resting on the ground. Slightly bend by stepping on the lowest section, move your foot up 8-10” and repeat until you have the curve you want. Be careful and don’t try to bend the conduit all at once, making numerous smaller bends works best. Once the conduit is curved, attach the Halex screw connector onto the flower end of the conduit, knock the center plug out of the Raco round cover plate and secure it to the screw connector (very easy, just sounds confusing).
Option 1: Drill a 7/8” inch hole in a large piece of wood. Insert the bent conduit stem (as seen below).
Option 2: Use buckets filled with gravel or sand to keep the flower upright.
Option 3: Simply push the stem into the ground if your event is outdoors.
Option 4: Make something up. If it works, share your wisdom with the rest of us!
Option 2: Use buckets filled with gravel or sand to keep the flower upright.
Option 3: Simply push the stem into the ground if your event is outdoors.
Option 4: Make something up. If it works, share your wisdom with the rest of us!
Finally, attach the completed flower using a lot of hot glue to the 3 ½” cover plate. You will need A LOT of hot glue. And just when you think it is secure, add more glue…just in case. You don’t want the wind taking off with the top of your flower! Now pool your fabric around the base (you can see this in her ceremony photos below) and –Viola! You are finished!!
And a few photos from their wedding to see how they used them for their pretty outdoor ceremony –be sure to check out their entire wedding feature here!